Jump to content
Gwen

The next project begins!

Recommended Posts

So my arcade table is like 95% done, but in my true ditzy nature i can never completely finish something without moving on to another project. Thus my next project is beginning.

I got the basic parts I need, and just need to get some wood to build the cabinet, which I'll be doing this weekend.

mqculPs.jpg

6hApNjK.jpg

 

Ok boys... bigger is not always better! I had originally purchased a 43" tv, but i saw the 49" go on sale and figured bigger would be better. The cabinet that I am following was an arcade/pinball cab and had a 43" tv, but had an arcade panel at the front. I confused myself and figured i dont need the panel, i'll go bigger and get more screen to fill up the cabinet. I didnt pay attention that going bigger will also make it wider. Now my cabinet is going to be 2 inches wider than a normls cabinet, and i have to get a custom piece that is going to cost $50 more. :4_joy:

The ideal size tv would be 47", but they did not have any.

This is going to be my playfield.

bAs7DK9.jpg

 

That's it for my pinball project for now. next week hopefully i'll have some more progress.

 

Here is my storage bench i painted to be like space invaders for my arcade room. This room is so messy right now... i'm not exactly sure where i'm going to put my pinball cabinet.

OCQ10bx.jpg

 

Here are my Donkey Kong shelves i made to keep up my arcade theme.

Nhuoldi.jpg

 

Some of the gaming nick knacks

8SvoMQq.jpg

4ZaAIDX.jpg

 

 

More updates to follow! ^.^

Share this post


Link to post
Share on other sites
16 minutes ago, Gwen said:

uggg.. ok i'll create an Imgur account. hold on.

 

ok does it work now?

Yes :)

Share this post


Link to post
Share on other sites
3 hours ago, Kibbelz said:

Or you could use the AGD filehost. Wither way i like what you've done.

The Wither way is to die in my Wither Farm so I can get Nether Stars. ;)

Share this post


Link to post
Share on other sites

Ok so I got some wood and started building the cabinet. My friend had a table saw, so i thought it might be easier, and I would get better cuts with the table saw, but it didn't work out that great. I would have been better doing it myself by hand. I ended up screwing up some measurements, and wasted a lot of wood. :4_joy:

Now i have to go buy some more wood.

 

I was able to build the back box. This is the top of the pinball table. It actually turned out pretty good. I need to putty some spots where the wood splintered, and to fill in some small gaps to make it totally smooth, but overall not to bad.

 

Back. The center hole will have a piece of wood on a hinge to close like a door.

MwXD7sV.jpg

 

Front

UsKfRnd.jpg

 

Side

8EKh8qD.jpg

 

Here is all the wood for the cab... unfortunately two of the largest pieces are bad.

L6fz6F5.jpg

 

Here are my gaming tins. Camera didn't take that great of a pic

6oXvXqU.jpg

 

Here they are with the lights off in the room.

sJvorih.jpg

 

Share this post


Link to post
Share on other sites

I know... I thought i had measured a few times, but I don't know what happened. I think converting my plans from mm to inches, then having to adjust some sizes to fit my larger TV, but forgetting to update some of the other matching sides, and just being out of my element and being at my friends house getting "help" got me all confuzzeled.

 

OH MY GOD this is expensive! I knew it was going to be expensive, but i didn't realize how expensive it was until I already jumped off the cliff. I probably could have got an older real pinball machine for the price I've dumped into this.

 

Thankfully i have some things that i was able to free from other sources, but I still need to dump some more money in to make this super awesome.

 

$319 - TV

$70 + more for screw up - Wood

$700 - rails, legs, bolts, buttons, plunger, digital plunger adapter, shipping

 

I still need to buy solenoids, LEDs, paint, solenoid controller relay, LED controller, upgrade my computer, other toys like shaker motor and fans. .

It's probably going to cost me about $12-1300 when I'm fully done, but i have enough right now to at least have something playable.

 

 

This is what i'm striving for. He talks a lot, so you might want to skip around if you are not that interested.

 

Share this post


Link to post
Share on other sites

Ok so new update...

 

I started building the cabinet, and got pretty far this weekend. It turned out pretty nice. I had to buy another sheet of plywood since i screwed up some pieces before... there was $30 down the drain :(

 

Cabinet

gtZ5tK4.jpg6uwuHkX.jpg

 

 

The "top". I had to do a weird 45 degree cut in the back to make it fit right. there was a gap that i didn't understand how they covered in the plans.

h5XRgST.jpg

 

45 degree edge pieces. I am so happy with how these cuts came out. I have just a small gap that i had to fill with putty due to the wood separating when i tried screwing the pieces together. Not bad for hand cutting with a circular saw!

 

This is where the gap is I mentioned earlier. having a straight piece of wood would leave a giant chunk missing in the corner where the 45 cut is. some of my screws were a little close to the edge and split the wood a little, but nothing putty wont fix!

MEnVyM6.jpg

 

Test fitting the coin door. This is mostly cosmetic. The lights work, and opening the door is mostly to get to the inside of the cabinet, but it doesn't actually take coins.

7gffbJK.jpg

 

Cabinet with the backbox

tK0QdtK.jpg

 

A little leg action

snRZsEr.jpg

 

That's it for now. I still have a few more holes i need to drill for the buttons, and a little more sanding, and then I can paint it. It's looking really nice up close!

Share this post


Link to post
Share on other sites

Ok so I finally did some more work. I had made my cabinet a little to narrow, and i didnt account for a button on the bottom of the tv,  so the tv would not fit when i tried to put it in the cabinet. I had to rout out a large groove, and now i can angle the tv in and it fits. This really took the wind out of my sails and i didnt want to deal with it for a long time, but i finally got it fixed. Now for the next part.... PAINTING the bottom cab. Really I think this is why it took me so long to fix the tv not fitting... i HATE painting, and i knew if i fixed it i would have to paint.

 

At this stage i could start playing. I just need to throw in my computer, wire the buttons, and I'm good. I can complete the top of the pinball later, as that is just eye candy, and does not affect playing the system.

 

Anyways, here are some more pics.

 

Just got TV fitted, and installed plunger

1ACUmsn.jpg

 

All of the buttons added, and legs attached

1OVDvgs.jpg

 

Right side with flipper buttons

aItXW31.jpg

 

Left side with flipper buttons

C1Ppfki.jpg

Share this post


Link to post
Share on other sites

Getting closer....

 

Not sure if you guys are still interested, but I have gotten closer to finally getting this thing done.

Sorry for the larger pics... not real sure how to size them... and I'm too lazy!

 

I finally painted the cabinet and added the buttons.

uOZ5Jnp.jpg

 

Side view

4gZk2Rc.jpg

 

My home made power box, and start of the wiring.

WclMvGG.jpg

 

Testing a Pinball FX 3 table

0TRllHi.jpg

 

Cleaned up the wiring a little. You can see the terminal blocks on the left that then connect to the controller card.

KkddBRZ.jpg

 

Front view of the inside of the cabinet.

wqQWFYO.jpg

 

Got the lights working!!!!!! I have to change the green and yellow button from 12v to 5v. They are too bright!

wD0B1pz.jpg

 

Painted the back box

Qv9OB2w.jpg

 

This is basically what the end product is going to look like. Right now everything does work. The plunger, flippers, launch ball... i can actually play a game now.

ss1NSWa.jpg

 

Next I will just have to save up money and buy my solenoids to give proper feedback, and have it feel less video gamey and more like a real pinball system.

Then its back to work on my arcade cabinet to get that completed.

 

Let me know what you guys think.

 

Share this post


Link to post
Share on other sites

Even closer... I just need to frame out the top screens with some thin wood i have, and then I'm basically done. I just need to do configuration now.

Then it's just make it cooler with adding the solenoids, motors, glass, upgrade my computer... but i'm going to have to wait a while for those.

 

Anyways... here are a few more pics.

 

Top monitors added

ElaJCxx.jpg

 

With the lights... kind of hard to see.

0mcq1KP.jpg

 

Easier to see.

3TT1b91.jpg

Share this post


Link to post
Share on other sites

yeah sure... I'm still in the learning process myself.. but once I get it completed more i'll post a guide on what i did, and where i got stuff from.

Share this post


Link to post
Share on other sites
2 hours ago, Gwen said:

yeah sure... I'm still in the learning process myself.. but once I get it completed more i'll post a guide on what i did, and where i got stuff from.

 

dope. i'll keep an eye out for it

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×